FMS FCX10 PRO TOYOTA LAND CRUISER LC80 RS V2 1/10 BRUSHLESS CRAWLER RTR

The FMS FCX10 PRO Toyota Land Cruiser LC80 RS V2 is a 1/10-scale brushless crawler built around the FCX10 P performance chassis. It combines licensed Toyota scale detail with the hardware serious trail drivers expect: portal axles, remotely lockable front and rear differentials, a two-speed transmission, 2S/3S brushless power and a 25 kg digital steering servo.

FCX10 PRO PERFORMANCE PLATFORM

• Dedicated 4WD drivetrain for predictable traction on technical trails and rock sections
• Portal axles raise the axle centerline to improve ground clearance without excessively raising the chassis
• Front and rear differentials lock independently from the transmitter, allowing open-differential steering or maximum locked traction as terrain demands
• Two-speed transmission supplies controlled low-range crawling and a faster high range with a manufacturer-rated maximum speed up to 12.4 mph
• Upgraded transmission housing and BATRAZZI Precipice 1.9-inch M/T tires
• Optional conversion hardware is available separately for DIG and alternate front/rear-drive configurations

BRUSHLESS POWER & LINEAR CONTROL

• 3541 2100Kv brushless motor delivers strong low-speed torque and smooth acceleration
• SL50A independent 2S/3S brushless ESC is separate from the receiver for easier service, replacement and future upgrades
• R11D-BS receiver paired with the MG11 11-channel 2.4GHz transmitter
• 25 kg digital steering servo provides the torque needed to turn loaded crawler tires on high-grip terrain
• FMS OPS control calibration is designed for precise, progressive throttle response at ultra-low speed
• The motor is designed for wet-condition use and the vehicle is splash-resistant; follow the manual and clean and dry the truck after wet operation

LICENSED TOYOTA SCALE DETAIL

• Officially authorized Toyota Land Cruiser LC80 body
• Snorkel, windshield wipers, door handles and off-road front bumper
• Roof rack with auxiliary lamps and rear access ladder
• Detailed cabin with dashboard, steering wheel and driver figure
• Scale rear lamps, license plate detail and external body trim

MAGNETIC LIGHTING SYSTEM

• Headlights
• Front turn signals
• Side turn signals
• Rear turn signals
• Reverse lights
• Magnetic body-to-chassis electrical connection eliminates a loose lighting cable when removing the body

CHASSIS & TRAIL CAPABILITY

• FCX10 P chassis engineered for performance crawling
• 76 mm ground clearance
• 51-degree approach angle and 42-degree departure angle
• 120 × 45 mm front and rear tires
• Long-wheelbase 325 mm layout for stability
• Full underside protection around the transmission and driveline

SPECIFICATIONS

BATTERY FITMENT

• Recommended: one 2S or 3S 5000mAh LiPo battery with XT60 connector
• Standard battery compartment: 140 × 47 × 40 mm
• Available compartment length without the receiver in that location: 170 × 47 × 40 mm
• Use a compatible balance charger and LiPo charging bag

IN THE BOX

• FMS FCX10 PRO Brushless Toyota Land Cruiser LC80 RS V2
• MG11 11-channel 2.4GHz transmitter
• Installed R11D-BS receiver
• Installed SL50A 2S/3S brushless ESC
• Installed 3541 2100Kv brushless motor
• Installed 25 kg digital steering servo
• Product manual

NEEDED TO COMPLETE

• One compatible 2S or 3S LiPo battery with XT60 connector
• Compatible LiPo balance charger and charging bag
• Four AA batteries for the transmitter

GASHEAD RC SETUP NOTES

• Use low range and locked differentials for steep, technical obstacles
• Unlock the differentials when a tighter, smoother steering response is more important than maximum traction
• Confirm steering endpoints and drivetrain functions before the first trail run
• Clean and dry the portal housings, driveshafts and chassis after water, mud or sand

READY SET: vehicle battery, charger, charging bag and four AA transmitter batteries are not included.